How do I Machine HDPE Plastic?

Written by hugh patterson
  • Share
  • Tweet
  • Share
  • Pin
  • Email
How do I Machine HDPE Plastic?
A sharp blade helps make cutting HDPE an easy process. (saw image by Kaarel from

High-density polythene, or HDPE, is an extremely popular plastic used for everything from cutting boards to boat parts. Its low friction makes it a comparable replacement for Nylon or Teflon. HDPE is also generally less expensive that Nylon or Teflon. It is easy to machine and, unlike acrylic, will not crack when being cut. Using conventional shop tools, HDPE can be machined into a number of useful parts.

Skill level:

Other People Are Reading

Things you need

  • Electric saw
  • Router
  • Drill
  • Palm sander
  • Utility knife
  • Grease pencil
  • Double-sided masking tape
  • Straight edge
  • Scrap lumber

Show MoreHide


  1. 1

    Cut the HDPE to the desired size with a table saw, radial arm saw, circular saw or jigsaw. The key to a good cut is to use sharp blades and a proper feed rate. The feed rate is how fast the material is pushed through the saw. If the piece is cut with a dull blade at too slow a feed rate, the material can melt against the blade. Use a 60- to 80-tooth, carbide-tipped blade. The feed rate should be roughly 70 to 90 feet per minute.

    How do I Machine HDPE Plastic?
    A jigsaw is a good choice when cutting curves in HDPE. (fretsaw image by Aleksandr Ugorenkov from
  2. 2

    Route cutouts or channels using a carbide router bit. Carbide bits last longer than standard bits when used for cutting plastic. If the router has an adjustable speed, set it around 18,000rpm. The feed rate should 8 to 16 feet per minute. For straight cuts or square cutouts, create a guide made from scrap lumber or plastic for the router to follow. Measure the distance from the bit to the outer edge of the router's bottom plate or collar. This is the distance to use when placing the guide. Apply double-sided tape to the guide to hold it on to the material. For cutouts, drill a pilot hole larger than the router bit, rather than plunge routing into the plastic.

  3. 3

    Mark any drilling locations using a grease pencil. This type of pencil will adhere to the HDPE whereas lead pencils will not. Use a drill bit with a 45- to 60-degree point. Flat drill bits tend to skip across the material rather than biting into it. The drilling speed should between 3,500rpm for thinner material--1/8 inch--and 450rpm for thicker material--1 inch. Drilling speeds are not as critical for HDPE as they are for harder plastics such as acrylic. HDPE is soft enough to drill without any lubrication.

    How do I Machine HDPE Plastic?
    HDPE is easy to drill due to the material's lower density. (Electric drill with a drill on a white background image by terex from
  4. 4

    Sand down material to finish the edges with 320-grit sandpaper. HDPE is softer than most plastics, therefore it sands faster than materials such as acrylic. For a clean or sharp edge, use a utility knife to scrape the material smooth. Hold the blade at a 60-degree angle to the material and lightly push the blade outward. Make sure there are no jagged edges that will catch the knife.

    How do I Machine HDPE Plastic?
    Carbide router bits work best for plastics. (router bit s image by Michael Cornelius from

Tips and warnings

  • HDPE is extremely difficult to glue. Therefore, using screws to join pieces together is best. Double-sided masking tape works well for temporarily joining HDPE.
  • HDPE has a low melting point so it can be heat-formed in the same way acrylic can.

Don't Miss

  • All types
  • Articles
  • Slideshows
  • Videos
  • Most relevant
  • Most popular
  • Most recent

No articles available

No slideshows available

No videos available

By using the site, you consent to the use of cookies. For more information, please see our Cookie policy.