How to Change a Whirlpool Refrigerator Door Gasket

Written by kenneth crawford
  • Share
  • Tweet
  • Share
  • Pin
  • Email
How to Change a Whirlpool Refrigerator Door Gasket
(Ablestock.com/AbleStock.com/Getty Images)

A metal retainer secures the Whirlpool refrigerator inside door panel and the door gasket to the inside of the door. When the time arrives to replace the door gasket, you will need to loosen the retainer. Changing the door gasket on a Whirlpool refrigerator may require adjustments to the inner door panel to obtain a secure seal. Replacement door gaskets are available at appliance repair shops and home improvement centres. The new gasket will be stiff, so you will need to soften the new gasket to make it easier to work with when installing.

Skill level:
Moderate

Other People Are Reading

Things you need

  • Replacement refrigerator gasket
  • Nut driver
  • Socket wrench

Show MoreHide

Instructions

  1. 1

    Fill your kitchen sink halfway with lukewarm water. Set the replacement refrigerator gasket in the water and let it soak while you are removing the old gasket. This will soften the gasket and make it more pliable to install.

  2. 2

    Remove the food from the inside door shelves of your refrigerator.

  3. 3

    Start at the top of the refrigerator and lift the bottom of the refrigerator door gasket up with your thumbs. You will see the hex heads of the retaining screws that secure the retainer to the door.

  4. 4

    Loosen the retaining screws with an appropriate size nut driver or socket wrench. Do not remove the screws. The retainer just needs to be loose enough to remove the door gasket.

  5. 5

    Continue loosening the retaining screw across the top of the door, down each side of the door and finally at the bottom of the door.

  6. 6

    Pull down the top corner of the refrigerator door gasket nearest the door hinge. Remove the gasket from the hinge side and top of the door. Continue pulling the gasket off of the handle side of the door and then the bottom.

  7. 7

    Clean away any torn pieces of gasket that may be between the retainer and the door panel. Pull the new door gasket out of the water and dry it with a towel.

  8. 8

    Position the new door gasket over the inside of the door. Place the top corner of the gasket between the retainer and the door panel on the hinge side of the door. Push the gasket behind the retainer all the way down the hinge side until you get to the bottom corner.

  9. 9

    Pull the top of the door gasket over the top corner on the handle side of the door. Push the gasket between the retainer and the door along the top of the refrigerator door. Continue pushing the gasket behind the retainer on the handle side of the door until you reach the bottom corner.

  10. 10

    Pull the hinge side bottom corner of the gasket until you can insert the gasket behind the retainer. Push the gasket into place along the bottom of the door. Use both of your thumbs to manoeuvre the handle side lower corner of the gasket behind the retainer.

  11. 11

    Tighten all of the retaining screws until the retainer is snug against the gasket, but do not tighten the screws fully. Close the refrigerator door to check the alignment of the door, door gasket and the front of the refrigerator. You should have a seal all the way around the door perimeter. Open the door, move the inside door panel as necessary by hand and recheck the alignment.

  12. 12

    Tighten all of the retaining screws with the nut driver or socket wrench. Place your food back in the refrigerator door shelves.

Don't Miss

Filter:
  • All types
  • Articles
  • Slideshows
  • Videos
Sort:
  • Most relevant
  • Most popular
  • Most recent

No articles available

No slideshows available

No videos available

By using the eHow.co.uk site, you consent to the use of cookies. For more information, please see our Cookie policy.