How to build your own pool table

Written by rachel aenne
  • Share
  • Tweet
  • Share
  • Pin
  • Email
How to build your own pool table
With your own pool table, you can practise whenever you want. (Getty creative)

Purchasing a pool table for your home can cost anywhere from £325 to £3,250 or more. Fortunately, with time, patience and a few tools, you can build your own pool table for a fraction of the price. By measuring the room you'll be putting the pool table in, you'll be able to build the table to your own specifications. You'll also be able to build the pool table to a height that is comfortable for you.

Other People Are Reading

Things you need

  • 254 by 127 cm (100"x50") flat wood, 5 to 10 cm (2 to 4 inches) thick
  • 7.6 metres (25 feet) of 12.5 by 12.5 cm (5"x5") wood
  • 4 wooden beams, 20 to 30 cm (8 to 12 inches) by 20 to 30 cm (8 to 12 inches)
  • Table saw
  • Scroll saw
  • Sandpaper
  • Electrical sander
  • Flathead screws
  • Drill
  • Pool table adhesive
  • Felt (254 by 127 cm (100"x50") )
  • Staple gun
  • L-brackets
  • Scissors
  • Nets
  • Bubble level

Show MoreHide

Instructions

  1. 1

    Measure the room you want to house your pool table. Make sure there is enough space to accommodate the pool table with four feet extra on each side. Determine the size you would like to build. A UK standard pool table is 7 feet by 4 feet (213 by 122 cm).

  2. 2

    Cut the flat wood into the size you would like for your pool table. Measure and mark the length and width of the intended table dimensions. Use a table saw. Ensure that the wood is perfectly flat. Sand the edges.

  3. 3

    Cut the pockets out of the flat wood with a scroll saw. The width of the pocket should be 1.6 times the width of a ball. Cut four corner pockets. Measure and cut two pockets in the center of each long side. Sand the edges.

  4. 4

    Cut the legs for the pool table out of the wooden beams. Make them all exactly the same length. A regulation pool table should be between 31 and 34 inches (79 and 86 cm).

  5. 5

    Place the legs upright on the floor where the four corners of the pool table will be. Move each leg 15 cm (6 inches) toward the centre to avoid interference with the corner pockets. Attach the table top to the legs with three screws per leg. Add L-brackets to the underside to increase stability.

  6. 6

    Cut six pieces of 125-cm (50-inch) wood strips for the ledges of the pool table. Cut spaces in the strips for the pockets. Secure the strips to the edges of the table with a screw every 30 cm (12 inches).

  7. 7

    Spray the surface of the pool table and the inside edge of the ledges with pool table adhesive. Lay the felt over the table without letting the felt fold or kink. Remove any air bubbles with a rolling pin. Make sure the felt is applied to the inside edge of the ledges. Cut excess felt off with sharp scissors. Secure the outside edge of felt with staples for extra security.

  8. 8

    Use a staple gun or screws to secure the nets to the pockets. Make sure each net can hold at least four billiard balls.

  9. 9

    Use a level at regular intervals down the entire length of the table. Make sure the table is completely level. If the height of a side needs to be adjusted, place wedges under the legs as necessary.

Don't Miss

Filter:
  • All types
  • Articles
  • Slideshows
  • Videos
Sort:
  • Most relevant
  • Most popular
  • Most recent

No articles available

No slideshows available

No videos available

By using the eHow.co.uk site, you consent to the use of cookies. For more information, please see our Cookie policy.