Ideas for airplanes using popsicle sticks

Written by roger delvenado
  • Share
  • Tweet
  • Share
  • Pin
  • Email
Ideas for airplanes using popsicle sticks
Popsicle sticks are great for building model aeroplanes. (Dynamic Graphics Group/Dynamic Graphics Group/Getty Images)

Popsicle sticks are great materials to use in craft projects. Cheap and easy to use, Popsicle sticks (or wooden tongue depressors) are the raw materials used to make models of everything from houses to aeroplanes. In fact, there are multiple ways to build aeroplanes with Popsicle sticks.

Other People Are Reading

Popsicle Stick Airplane Ornament

This simple and fun craft project for kids is all about the holidays. Using two Popsicle sticks, tacky glue, a few buttons, some scissors and a small Santa Claus figurine, kids can fashion their own Christmas aeroplane. The Popsicle sticks, held together with tacky glue, form the body and wings of the plane and two buttons stuck to the body make the plane's wheels. Add a propeller and some decorations and then plop Santa in the cockpit. Use tacky glue and string to create a hanger for the plane and then hang it on the tree for everyone to enjoy.

Five Popsicle Stick Airplane

Five Popsicle sticks is all it takes to make this simple, flyable aeroplane. Tension holds the sticks together. Start with three Popsicle sticks stacked on top of each other and then fan them out, like fanning out a hand of cards, so that they make a shape similar to a "W." Weave a fourth Popsicle stick perpendicularly into the "W" going over one stick, under the next and over the third. This stick should be somewhat near the middle of the plane. Repeat the weaving process with the fifth and final Popsicle stick near the back, wide end of the plane. The tension from weaving the two cross-sticks through the "W" frame holds the plane together.

Popsicle Stick Bi-plane

With a few Popsicle sticks, some glue, a little paint and a clothespin, kids (or adults) can whip together a fun model of an old-time biplane. The clothespin needs to be separated into two pieces (i.e., the wood removed from the wire spring). Glue the two pieces of the clothespin together with the flat sides of each piece touching. This is the body of the biplane. Glue a Popsicle stick across the top of the plane body, just behind the thickest part, and add another stick below to complete the wings. Use additional Popsicle sticks, cut into smaller pieces, to fashion an upright tail and tail-wings to complete the biplane. Paint or decorate any way you like.

Popsicle Stick Airplane Model Computer Housing

This Popsicle stick aeroplane craft requires a lot of hours and a lot of Popsicle sticks. Using hundreds, if not thousands, of Popsicle sticks and plenty of tubes of glue, this project creates an aeroplane body about 3 feet long with wings of similar length. Begin by laying a foundation of Popsicle sticks laid side-by-side upon which the rest of the plane will be built. Begin stacking and gluing more sticks down the length of the base row of Popsicle sticks such that the base row is held in place by being glued to the row above. Once this base is secure, continue adding layers of Popsicle sticks with sticks laid at right angles across the base between each layer to add stability to the model. The body of the plane will be the width of only one Popsicle stick. As the sides are built up, leave a gap in the panelling that will eventually hold a hard drive and also serve as a space for the wings. Place the hard drive into the plane's body, leaving open a space for power and connecting cables to exit the plane's body. When the hard drive is properly situated, finish building the sides and add another row of Popsicle sticks at right angles to finish the plane's ceiling. Follow similar steps to build the wings. (Don't forget to leave a space above the area holding the hard drive into which to fit the wings.) You may need to cut or bend other Popsicle sticks to make a tail and cockpit for the plane. If enjoying the sight of a painstakingly crafted Popsicle stick replica of a plane isn't enough for you, remove the wings and Popsicle stick side-panelling and insert a motherboard into the body of the plane. At the very least, it will make a unique housing for some computing power.

Don't Miss

Filter:
  • All types
  • Articles
  • Slideshows
  • Videos
Sort:
  • Most relevant
  • Most popular
  • Most recent

No articles available

No slideshows available

No videos available

By using the eHow.co.uk site, you consent to the use of cookies. For more information, please see our Cookie policy.