Flat spiral bracelet instructions

Written by kathryn hatter
  • Share
  • Tweet
  • Share
  • Pin
  • Email
Flat spiral bracelet instructions
Make a flat spiral bracelet out of coloful beads. (beads image by Alison Bowden from Fotolia.com)

Beading can be as basic or as intricate as you desire to create jewellery pieces that will stand out as beautiful representations of your creativity. Explore some of the many beading patterns for making pieces out of beading thread and tiny seed beads. When you weave these beads together and intersperse them with larger beads, the effect is stunning and lovely. Beginning beaders can learn to make a flat spiral bracelet using seed beads and round crystals.

Skill level:
Moderately Easy

Other People Are Reading

Things you need

  • Nylon beading thread
  • Beading needle (size 12)
  • Scissors
  • 28 round crystal beads (6mm)
  • 50 round crystal beads (4mm)
  • 5 grams seed beads (11/0)
  • Toggle clasp

Show MoreHide

Instructions

  1. 1

    Cut a 3-yard length of nylon beading thread and thread the beading needle onto the beading thread.

  2. 2

    Pick up two 6mm beads onto the needle and push the beads along the thread until they reach the end of the thread. Leave a 10-inch tail on the other end of the two beads.

  3. 3

    Thread four seed beads, one 4mm bead and four more seed beads onto the needle. Insert the needle back through the two 6mm beads again from the other side of the beads to create a loop with the seed beads. Pull the beading thread taut.

  4. 4

    Repeat Step 3 to make a second loop around the first two 6mm beads, except place the second loop on the other side of the two 6mm beads.

  5. 5

    Pick up one 6mm bead onto the needle and push it along the thread so it is snug against the other 6mm beads.

  6. 6

    Thread four seed beads, one 4mm bead and four more seed beads onto the needle. Insert the needle back through the last two 6mm beads from the other side of the beads to create a loop with the seed beads. Pull the beading thread taut.

  7. 7

    Repeat Step 6 to create a second loop around this 6mm bead, placing the second loop on the other side of the 6mm bead.

  8. 8

    Repeat Steps 5 through 7 until the bracelet is approximately 1.5 inches less than your desired finished length. Using all 28 6mm beads will create a bracelet that is approximately 7.5 inches.

  9. 9

    Thread three seed beads, half the toggle clasp and three more seed beads onto the needle. Insert the needle through the last two 6mm beads of your pattern and pull the beading thread taut. Insert the needle back through the beads you strung at the end of the pattern until you reach the point where the toggle clasp attaches to the bracelet. Insert the needle back through five or six beads going the other way and then reverse again. This secures the beading thread before you tie it off. Insert your needle through the beads so the thread extends off from a centre 6mm bead and tie your beading thread off at this point with a knot. Bury the beading thread by inserting it through one or two more beads and snip off the excess beading thread to finish this end of the bracelet.

  10. 10

    Repeat Step 9 on the other side of the bracelet with the other half of the toggle clasp to finish the bracelet.

Don't Miss

Filter:
  • All types
  • Articles
  • Slideshows
  • Videos
Sort:
  • Most relevant
  • Most popular
  • Most recent

No articles available

No slideshows available

No videos available

By using the eHow.co.uk site, you consent to the use of cookies. For more information, please see our Cookie policy.