The Chevrolet full-size van was manufactured with six-cylinder inline, V6 and V8 engines and was most commonly used as a cargo van or as a base for conversion vans. The engine and transmission should be removed as a complete unit. The process for removing an engine is complex, so before you begin make sure you have plenty of room to work, plenty of time and all of the tools you'll need.
Disconnect the ground cable from the negative battery terminal. Disconnect the positive cable and remove the battery.
Remove the engine cover, if equipped.
Remove the air cleaner housing.
Separate the kickdown cable from the throttle linkage (automatic transmission).
Separate the throttle cable from the carburettor, and remove the carburettor.
Remove the accessory drive belts.
Label each wire attached to the engine for ease of installation.
Disconnect all electrical harnesses from the engine.
Open the petcock valve on the bottom of the radiator and drain all the coolant from the cooling system.
Remove the coolant reserve tank.
Remove the grille and upper radiator support.
Disconnect the transmission cooler lines (automatic transmission) from the radiator. Plug the lines and secure them off to the side of the vehicle.
Disconnect the radiator hoses from the engine and remove the radiator.
Remove the air conditioning condenser mounting bolts and secure the condenser out of the way with the hoses still attached.
Remove the water pump pulley and fan.
Remove the air conditioning compressor and secure it out of the way without disconnecting the lines.
Unbolt the power steering pump and secure it out of the way without disconnecting the lines.
Remove the alternator. Be sure to label the wires for reassembly.
Separate the fuel line from the fuel pump and plug the end.
Remove and vacuum hoses. Label each for reassembly.
Lift the vehicle according to instructions listed in the owner's manual and support with jack stands underneath the frame.
Remove the oil pan plug and drain the engine oil.
Disconnect the wires to the starter motor. Label each wire for reinstallation. Remove the two bolts that connect the starter to the engine block. Remove the starter motor.
Separate the head pipe from the exhaust manifolds.
Slide the engine hoist into position at the front of the vehicle.
Install a lift plate on the carburettor mounting surface.
Remove the straps that connect the rear driveshaft u-joint to the pinion yoke on the rear axle. Then slide the driveshaft rearward, underneath the axle, to remove it. Plug the transmission tailhousing to prevent loss of fluid.
Disconnect the speedometer cable from the transmission.
Remove the bolts that connect the transmission crossmember to the frame. Remove the transmission crossmember.
Remove the clutch linkage and cross shaft (manual transmission).
Connect the engine hoist to the lift plate.
Raise the engine hoist just enough to take the weight off the motor mounts.
Check that all the connections between the vehicle and the engine, except the motor mounts, have been separated.
Remove the motor mount through bolts.
Slide the engine hoist away from the vehicle and remove the engine and transmission as a complete unit. You may have to tilt the engine to clear the firewall.
Spray a penetrating oil such as WD-40 on all fasteners the night before you intend to remove the engine. This will aid in disassembly.
Make sure the engine hoist you use has a higher weight capacity rating than the engine you intend to remove. Once you remove the engine, you must mount in an engine-specific stand. Allowing the engine to sit on the oil pan will damage the oil pan.
Tips and warnings
- Spray a penetrating oil such as WD-40 on all fasteners the night before you intend to remove the engine. This will aid in disassembly.
- Make sure the engine hoist you use has a higher weight capacity rating than the engine you intend to remove.
- Once you remove the engine, you must mount in an engine-specific stand. Allowing the engine to sit on the oil pan will damage the oil pan.
Things you need
- Engine hoist
- Lift plate
- Floor Jack
- Jack stands
- Socket set
- Breaker bar
- Wrench set
- Phillips Screwdriver
- Flat blade screwdriver
- Needle nose pliers
- Waste oil/coolant pan
- Permanent markers
- Penetrating oil (WD-40)
- Plugs for transmission cooler and fuel lines
- Plug for transmission tailhousing
- Steel wire or plastic ties