How to Design a 3D Kitchen Using Adobe Photoshop

Written by andrew dewitt
  • Share
  • Tweet
  • Share
  • Pin
  • Email
How to Design a 3D Kitchen Using Adobe Photoshop
(Illustrations by Andrew DeWitt)

Adobe Photoshop is an excellent tool for creating just about any digital image. While Photoshop is not normally used to create 3-D artwork or designs, there are options and tools that can be used to create the effect. These techniques can be picked up with relative ease compared to using a more traditional 3-D-based design software. Once completed, your kitchen design can be used to create a full overhaul of your existing kitchen layout.

Skill level:
Moderately Challenging

Other People Are Reading

Things you need

  • Adobe Photoshop
  • Mouse or digital tablet (tablet preferred)

Show MoreHide

Instructions

  1. 1

    Click the line tool and set the pixel size to 4. Click the circle on the middle left section of the screen and create a small (1-inch diameter or less) dot for the vanishing point of the illustration. This will allow you to create a 3-D kitchen using single point perspective. Draw a rectangle around the perspective point so that the dot is in the upper right corner for the back wall. Click the line tool on the upper right-hand corner and drag it to the upper right hand corner to create a ceiling line. Click on the bottom right-hand corner of the back wall rectangle and drag this to bottom right corner of the screen to create the bottom of the right wall.

    How to Design a 3D Kitchen Using Adobe Photoshop
  2. 2

    Click the line tool inside the dot and drag the tool diagonally to the upper right to create the top of the cupboard. Click and drag another line just under this to create the bottom front edge of the cupboard. Click on the top cupboard line halfway up the line and drag a vertical line down to connect to the bottom front edge of the cupboard. This will create the end of the cupboard.

  3. 3

    Click in the bottom left corner of the cupboard and drag a horizontal line across the screen to the right to create the bottom of the cupboards. Click inside the dot and drag two lines going diagonally to the bottom right corner of the screen to create the top of the oven and kitchen counter. Click inside the dot and drag a line down and to the right so it goes off the middle bottom right of the screen. This will create the bottom of the kitchen counters and oven. Draw a rectangle with your line tool to the left of the perspective point to create the refrigerator. Click on the upper right and bottom right corner of the refrigerator and drag a line from each corner into the perspective point.

    How to Design a 3D Kitchen Using Adobe Photoshop
  4. 4

    Click on the line denoting the front edge of the kitchen counter, directly to the left of the back wall. Drag a line horizontally to the right until you hit the back edge of the kitchen counter. Click at the same point where the horizontal line was started and drag a vertical line down from this point to the bottom edge of the kitchen counter. This will create the back corner of the kitchen counter.

    How to Design a 3D Kitchen Using Adobe Photoshop
  5. 5

    Add three vertical lines inside the cupboards to create the separate cupboard doors. Click inside the dot and drag a diagonal line that is between the bottom of the cupboard and the top back of the kitchen counter. Add four vertical lines, one near the end of the counters, two grouped close together near the bottom right of the screen to create the top right section of the oven, and one in between to show the left end of the oven. Add two perpendicular horizontal lines to create the right side edge, and then two more perpendicular vertical lines to show the rest of the right side edge of the stove. Repeat this on the left end of the stove.

  6. 6

    Add the handles to the refrigerator and cupboards with small rectangles that you create with vertical lines. Add the cabinets to the kitchen counter with two diagonal rectangles under the right side of the kitchen counter. Click on the square brush for the eraser and set the size to 25 pixels. Erase all the overlapping or unnecessary perspective lines you used to create the cupboards, oven, refrigerator and kitchen counter.

    How to Design a 3D Kitchen Using Adobe Photoshop
  7. 7

    Use the paint bucket tool to add colour or shading to the picture. Click on the colour you would like and dump this on the area you want coloured. Create shadows by choosing a colour two shades darker and dumping that on the underside or side areas of the object. Save the image as a Jpeg at maximum resolution. You can take this design to an architect or interior designer, and they will help you bring the design to life.

    How to Design a 3D Kitchen Using Adobe Photoshop

Tips and warnings

  • Use Ctrl+Z to quickly undo any mistakes you make without having to reload your work.
  • Save your work often in case there is a power outage.

Don't Miss

Filter:
  • All types
  • Articles
  • Slideshows
  • Videos
Sort:
  • Most relevant
  • Most popular
  • Most recent

No articles available

No slideshows available

No videos available

By using the eHow.co.uk site, you consent to the use of cookies. For more information, please see our Cookie policy.